How to Replace Analog Thermostat with Digital?

Substituting your analog thermostat with a digital one is an excellent way to save on your heating bill because digital thermostats can control the temperature in your home more accurately. New digital thermostats can save you up to 15% money on your heating bills. I think that’s more than enough reason why you should do it as soon as possible. My most current little project was replacing the analog thermostat with a digital one. I will tell you step by step how I did it. How to Replace the Analog Thermostat with a Digital? So How to Replace Analog Thermostat With Digital? In short, to replace the analog thermostat with a digital, you’ll first need to turn off the power in the house, remove the faceplate from the current thermostat, label the wires, detach the wires and remove the cover, mount the new thermostat, rewire it, and attach the faceplate. Ensure you read the instructions for your new thermostat thoroughly before you start with the work because it is very important for every time you are operating with electricity. Therefore, turn off the power to your heating and cooling system! You can do this by either going to the fuse box or circuit breaker or if a light switch regulates your thermostat. Just ensure that the switch is switched off. On Amazon, you can check the latest Digital Thermostats. After turning off the breaker box’s power, you should always, always, ALWAYS, confirm the power is shut off with a voltage tester and/multimeter. NEVER assume the power is off. A line voltage of 240 can kill you. Remove the faceplate and detach the wires. Since some thermostats comprise mercury, your old thermostat will need to be recycled. You can look on Google to see where you can recycle it. Twist the back part of the thermostat onto the wall (after drawing the wires through space). Look at your directions and check the diagram to recognize which wires get connected where. After wires are attached, you can connect the digital thermostat. Depending on the type of your new thermostat, the number of batteries will differ. Finally, connect the base and screw in position. Switch the power back on, and you’re finished! To see the detailed principle of How Does an Analog Thermostat Work, read this article. Why Analog Thermostat Is Bad? Reasons Why You Need To Replace Your Analog Thermostat Analog Thermostats are not accurate and can deviate by a few degrees from the set temperature resulting in an additional energy cost and with a larger bill. Therefore, it is desirable to replace them with digital ones. Some people are used to their old thermostats, that they have been using them for so many times during the years. At that same time, you were worried about how much the energy bill will be, unknowing the analog thermostat you have was wasting more money and energy than it should. This extra expense, particularly in the winter months, was caused by the analog thermostat, which didn’t hold the close temperature span you desired. Therefore, you raised and lowered the thermostat setting as much as four or five degrees each time to meet your needs. When you raised the setting on your analog thermostat for more than two degrees, you could not get the desired temperature, rather the temperature went higher than you set it. Digital thermostats have more accurate temperature sensitivity providing your place with greater comfort with less costly utility bills. These thermostats come as either programmable or non-programmable – your decision. Therefore, the digital thermostat is a must-have in every house. Save cash, preserve energy, go green. Replace Analog Thermostat With Digital – Step by Step The process of replacing an analog thermostat with a digital one consists of 9 simple steps that we will explain here in detail. So let’s start! Step 1: Carefully Choose New Thermostat Before installing a new thermostat, you must check your home’s compatibility. Houses are wired in two ways, line voltage, and low voltage, and you’ll want to buy a thermostat that will operate with your particular heating and cooling system. Therefore, choosing the right digital thermostats is important. Step 2: Turn Off Power to The Furnace Crucial: Switch off all power to the heating and cooling system before performing any electrical work to bypass any chance of electrocution or injury. HVAC systems are powered down at the breaker box. The power for some furnaces can be found directly on the boiler, generally with a toggle switch. It is also a great practice to switch your current analog stat all the way down prior to detaching. Step 3: Remove the Cover From the Current Thermostat With the wires opened, you will be ready to test the wires with a circuit tester to confirm that the power is off. See the type and number of wires to discover your thermostat’s compatibility. Line thermostats will be with two thick wires, while a low voltage stat will be with anywhere from two to eight small-gauge wires. Warning: Many older analog thermostats hold a glass tube of mercury. Mercury is regarded as a hazardous material and needs to be disposed of correctly. To see the thermostat cable color codes, read this article. Step 4: Mark the Wires You will want to mark the wires. Take a photo of, or note where the wires are connected before detaching them. This is very important! If you connect the wire incorrectly, the thermostat will not work. Note: They are not always color-coded or the identical for each thermostat. For example, if the green wire fits the G terminal, the corresponding wire must be inserted into the new stat terminal. Step 5: Detach the Wires and Remove the Wall Cover You must unscrew each wire from the terminal and also unscrew the wall mount as well. The wall mount will usually have one screw on each side. Examine to see if the current drywall fasteners follow with the new thermostat wall mount. If they don’t, you must connect the drywall anchors in the proper location. Note: I suggest that you secure the loose wires, using a tape, so they

Spread the love
Translate »