Syston · Cable planning tools

Cable calculators.
Plan with clarity.

Five practical tools for quantities, dimensions and DC circuit estimates. Start with documented inputs. See the calculation and its limits.

Choose your
starting point.

Open a tool below. Inputs stay on this page and are not sent as an inquiry. Calculations require JavaScript; methods and guidance remain readable without it.

Enable JavaScript to calculate. Formulas and references remain available below.

01DC Voltage DropEstimate loss along a two-conductor circuit using documented resistance.

Use the resistance for one conductor at the temperature stated in its specification. The return conductor is included in the calculation.

Enter your values, then calculate.

Method & conditions

Loop resistance = 2 × one-way length × resistance per unit length. Voltage drop = current × loop resistance. Estimated load-end voltage = supply voltage − drop.

Assumes equal outgoing and return conductors and a stated, constant DC current. Excludes connectors, splices, temperature adjustment, AC reactance and power-source regulation. Material and construction are represented by your resistance input; no copper or aluminum multiplier is assumed. This does not select a gauge or establish ampacity.

02Wire Gauge & Current ReviewConvert nominal AWG area and compare current with a limit you have verified.

Gauge geometry and current capacity are separate checks. Enter an allowable current only after it has been established for the specific cable, installation and conditions.

Enter your values, then calculate.

Method & conditions

Nominal AWG diameter in mm = 0.127 × 92^((36 − AWG)/39). Nominal conductor area = π × diameter² / 4. An entered metric area gives a continuous geometric AWG index, not an interchangeable product size.

AWG geometry follows NBS Handbook 100, section 2.2. Nominal solid-wire diameter is not the outside diameter of stranded or insulated cable. Current utilization = planned current ÷ your verified allowable current × 100. No generic ampacity table, temperature factor or cable-rating shortcut is used. A numerical comparison is not engineering approval.

03Conduit FillCalculate circular cable area as a percentage of the actual conduit interior.

Enter the actual inside diameter from the conduit manufacturer, not the nominal trade size. Use the overall outside diameter of each complete cable.

Cable 1

Enter your values, then calculate.

Method & conditions

Cable area = Σ(quantity × π × overall diameter² / 4). Conduit area = π × inside diameter² / 4. Fill = cable area ÷ conduit area × 100.

Only visible cable rows are included. All dimensions are converted to inches before calculation. This is a geometric estimate for circular cables and conduit; it does not determine a permitted fill limit or account for pulling, bends, jamming, heat or noncircular constructions. Have applicable limits reviewed for the actual installation.

04Cable Length EstimatorBuild a preliminary takeoff and package total from your planned runs.

Estimate an equal-length set of runs, add your allowance, then round to a package length. Package sizes are planning inputs, not confirmation of a sellable SKU.

Enter your values, then calculate.

Method & conditions

Base length = run count × average run length. Planned length = base length × (1 + allowance / 100). Preliminary packages = planned length ÷ package length, rounded up.

This total-length estimate does not allocate individual cuts or guarantee uninterrupted runs. Confirm routing, slack, termination allowance, actual packaging, availability and the complete ordering SKU before purchase.

05Low-Voltage DC Power PlannerEstimate nominal total current and loss for a shared DC cable run.

Model identical devices at the end of one shared outgoing-and-return circuit. Distributed taps or separate home runs require a different circuit model.

Enter your values, then calculate.

Method & conditions

Nominal current = device count × per-device current. If watts are entered, per-device nominal current = watts ÷ nominal supply voltage. Drop = nominal current × two-conductor loop resistance.

Uses that nominal current as a constant-current estimate. It does not solve constant-power behavior as voltage falls, startup or inrush, power-supply sizing, PoE, AC loads or distributed branches. Enter resistance for the actual conductor material and operating conditions. This is not a supply or cable approval.

Inputs before outputs

Keep the specification
within reach.

Use the exact product’s resistance, construction, dimensions and stated conditions. A calculator cannot replace that information.

Calculation references & unit conventions

The DC tools apply Ohm’s law and nominal power/current relationships. The gauge tool uses AWG geometry from NBS Handbook 100; this historical geometry reference is not an installation-code or ampacity source. Length and diameter conversions use 1 ft = 0.3048 m and 1 in = 25.4 mm exactly.

Useful context

Know what
the result means.

Does a result approve a cable or installation?

No. These tools calculate stated mathematical relationships using your inputs. They do not establish code compliance, ampacity, equipment compatibility or installation permission. Consult a qualified electrician or engineer for the actual project.

Where do I find resistance and diameter values?

Use the specification for the exact cable and the conduit manufacturer’s dimensions. Use resistance for one conductor, with its stated temperature and units. For conduit fill, use the complete cable outside diameter and the actual conduit inside diameter—not the conductor size or nominal conduit trade size.

Is 3% voltage drop always the required limit?

No universal acceptance limit is applied here. Compare the calculated voltage with equipment requirements and the applicable project criteria. The tools report the arithmetic without issuing a pass or an approved wire-size recommendation.

Are AWG and metric sizes interchangeable?

No. The gauge tool converts nominal geometric area. A similar area does not establish an equivalent cable construction, electrical rating, certification or available product. Confirm the exact model and its specification.

Can I use the package total as a quote?

No. The length estimator prepares a preliminary quantity only. Confirm continuous-run cuts, packaging, SKU, price, stock and lead time with Syston before ordering.

From estimate to inquiry

Bring the part number.
Keep the context.

For product documentation or an inquiry, share the Syston part number, quantity, required length and relevant project requirements.

Syston supplies wire and cable products. These tools provide mathematical planning estimates, not technical advice, installation instructions, code approval or a quotation. Consult a qualified electrician or engineer for project design, code applicability and installation.

Spread the love
Translate »